Von Duprin Escape Hardware - Flood Defence Doors

18 February 2015

Von Duprin - 98/9957 - Surface Mounted Three Point Latching Device

Protection at Flood Defence Doors

98/9957 - Surface Mounted Three Point Latching Device

PAS 1188-1:2009. Flood Protection Products. Specification. Part 1: Building Aperture Products

Effective July 2014 and in association with our colleagues at Loddon Door Services Ltd, Relcross is pleased to announce that the following product is certified for use on outward opening flood defence doors:

Specifically:

PAS 1188-1:2009. Flood protection products. Specification. Part 1: Building Aperture Products

PAS 1188-1 applies to flood protection products used in the temporary sealing of building apertures and entrances to properties, in the event of static flood water rising up to a level between 600 mm and 900 mm above ground level.

98/9957 - Surface Mounted Three Point Latching Device

Characteristics

Our flagship range of architectural grade escape devices includes the 98 Series with its smooth mechanism case and the established 99 Series with its familiar grooved design. The two styles are mechanically and dimensionally identical and provide a wide selection of additional features to suit many applications.

The Quiet One®

A fluid dampener decelerates the touch bar on its return stroke and eliminates most noise associated with exit device operations. Furnished on all 98/99 Series Exit Devices

UK Fire Certification in accordance with EN 1634-1:2000 (timber)
WFRC No. C132276 120mins BS EN 1125:1997

CE Certified.

Features & Benefits

Recommendations for Installing & Fixing

In accordance with BS EN 1125:1997 Annexe A (informative) the device should be installed with the touch bar normally at a height between 900mm and 1100mm from the finished floor level when the door is in the secure position. Where it is known that the majority of the occupants of the premises will be young children, it is acceptable to reduce the fixing height accordingly.

Strikes for 9857/9957 Surface Mounted Vertical Rod Devices

299 Top & Middle Roller Strike with 21mm projection (top), used with conventional frames where a reveal >32mm exists, (middle) used with conventional frames where the door stile width >121mm permits the necessary back set.

248L-4 Bottom Strike for use with flat top thresholds. Since the strike projects by 10mm care should be taken to ensure installation does not pose a trip hazard

304L Optional Bottom Strike for use where a mortice installation is desired.

Please note -

Both the 248L-4 & 304L Bottom Strikes are supplied as standard with all surface mounted vertical rod devices.

Optional Trim (for Outside Access)

Please refer to the 98/9957 Data Sheet (part 2) on the next tab.

   9857/9957 Series - Three Point Latching Device Standard Trim

How to Specify or Order

9857 Surface Mounted Three Point Latching Device for Doors <915mm
9857 Surface Mounted Three Point Latching Device for Doors <1220mm

9957 Surface Mounted Three Point Latching Device for Doors <915mm
9957 Surface Mounted Three Point Latching Device for Doors <1220mm

add suffix -

EO - Exit Only
DT - Dummy Trim
NL - Night Latch Trim
TP - Thumb Piece Trim
K - Knob Trim
L - Lever Trim

Finishes

US28 - Satin Anodized Aluminium
US32D - Satin Stainless Steel (98 Series)

see also:

Escape Hardware

For more information relating to this specialist area, please contact us via E Mail or call the Sales Office on  +44 (0)1380 729600. We shall be pleased to assist you with your specification.

 
Copyright © 2017 Relcross Ltd  |  All Rights Reserved
Relcross Ltd
Hambleton Avenue
Devizes
Wiltshire
SN10 2RT

t: 01380 729 600

w: www.relcross.co.uk
e: j.livesey@relcross.co.uk
Quick Enquiry

Make an enquiry

Please fill out this form and we will get back to you as soon as possible.


*Your name is required.

*Your email address is required.

*Please enter a valid email address.